Skip to Content

UR4-P360i

Program Your Remote
The UR4-P360i is a 4 device universal remote control that will control your cable box and up to 3 additonal devices, including TV's, VCR's and Audio devices.

Download Remote Manual
Common Remote Keys

Control a Device

Select a Topic

  • Upgraded Features

    URC is introducing new, upgraded features in all cable remote control models. These require a very slight modification of programming steps.

    These changes are for new remote orders delivered after 3/1/2013.

    Download the NEW set up instructions

  • Batteries
    Before you program or operate the remote control, you must install two new AA alkaline batteries.

    STEP 1 Remove the battery compartment cover on the back of your remote control.

    STEP 2 Check battery polarity carefully, and install the batteries as shown in the illustration inside the battery compartment.

    STEP 3 Replace the battery compartment cover.
  • Introduction
    The UR4-P360i is designed to operate the Scientific Atlanta Explorer and 8600X cable set-top boxes. This remote can also be programmed to operate the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below.

    CBL: Cable Set-top Box
    TV: Televisions
    VCR: VCRs and DVD players
    AUD: Audio Receivers


    Note: For TV/VCR Combo Units, set up the TV functions using the TV device codes and the VCR functions using the VCR device codes.

    Features include:
    - Large glow-in-the-dark buttons
    - Compatibility with DVR and On Demand features
    - Factory programmed to Time Warner Cable Specifications
    - Simple programming methods
    - Channel and Volume lock to provide ease of operation
    - Dedicated power buttons for each device
  • Replacing Batteries
    Before you program or operate the remote control, you must install two new AA alkaline batteries.

    STEP 1 Remove the battery compartment cover on the back of your remote control.

    STEP 2 Check battery polarity carefully, and install the batteries as shown in the illustration inside the battery compartment.

    STEP 3 Replace the battery compartment cover.
  • Operations
    Default settings for the remote control are as follows:

    Component Default: CABLE
    Channel Default: CABLE - Default controls for Channel +/- and numeric keys are through the CABLE device.
    Volume Default: Volume and Mute control are automatically transferred to the TV device.

    Refer to Programming Volume Control" for information on changing these settings."
  • Programming the Remote Control
    There are two ways you can program your UR4-P360i remote:

    The Pre-Programmed 3-Digit Code Method
    The Auto-Search Method


    The Pre-Programmed 3-Digit Code Method allows you to setup all the buttons for a device by entering 3-digit code numbers that correspond to a particular Component's manufacturer/brand.

    The Auto-Search Method scans through all the codes in the remote control in order to find the correct code for your device.

    IMPORTANT SETUP NOTE!
    In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR, or AUD button, depending on what device you are programming the remote to operate.

    When you are in setup mode, the Device LED will light for 20 seconds. If you do not press a button within 20 seconds, the LED light will turn off and exit setup mode. You will need to start the programming process over if this occurs.
  • Pre-Programmed 3-Digit Code Programming Method
    STEP 1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, DVD, etc.).

    STEP 2 Press the [DEVICE] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that the remote is in the programming mode. The LED will remain on for 20 seconds and the next step must be entered while the LED is on.

    STEP 3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand device (codes can be found in the code tables in the user guide or online). If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.

    Note: When the equipment turns off you can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above using the next three digit code number from the brand list.

    STEP 4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.

    Note: When programming the VCR device be sure the VCR/VOD switch is in the VCR position.
  • Auto-Search Programming Method
    If the Pre-Programmed 3-digit code method is unsuccessful or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following these steps:

    STEP 1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, DVD, etc.).

    STEP2 Press the [DEVICE] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that the remote is in the programming mode. The LED will remain on for 20 seconds and the next step must be entered while the LED is on.

    STEP 3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.

    Note: When the equipment turns off you can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, turn the device back on and repeat the instructions from STEP 3 to continue the Auto Search Method

    STEP 4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.

    Note: When programming the VCR device be sure the VCR/VOD switch is in the VCR position.
  • To Identify the 3-Digit Code Programmed for a Device
    The 3-Digit code that is programmed into the remote can be identified by following these steps:

    STEP 1 Press the [DEVICE] button and the [SELECT] button simultaneously for three seconds.

    STEP 2 Press the [INFO] button. The Device LED will blink a number of times indicating the number for each digit for the code. Each digit is separated by a one second interval of the LED being off.

    Example: One blink, (pause) three blinks, (pause) eight blinks indicates code number 138.

    Note: Ten blinks indicates the number 0.
  • Programming the System On/Off Button
    The System On/Off button can be programmed to send up to five Power On/Off commands with one button press. The remote control is factory programmed to send power commands for all five devices. The System On/Off button can be reprogrammed to send commands for the devices you choose by following these steps:

    STEP 1 Press the [CBL] button.

    STEP 2 Press the [SYSTEM ON/OFF] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.

    STEP 3 Press the first [DEVICE] button you want to store power commands for in the [SYSTEM ON/OFF] button and then press [POWER]. Repeat this for the other components you want to turn on/off with the [SYSTEM ON/OFF] button.

    Example: [CBL], [Power], [TV], [Power]. etc.

    STEP 4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.
  • Programming Volume Control
    Volume and Mute control are automatically transferred to the TV for all devices.

    If you wish to operate the volume controls via the cable set-top box follow these steps:
    STEP 1 Press the [CBL] button and [SELECT] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.

    STEP 2 Press the [VOL+] button. The device LED will blink.

    STEP 3 Press [CBL] button. The device LED will blink twice to confirm the programming. Now the volume will default to the Cable Set-top Box allowing you to adjust the cable set-top box volume when the remote control is in CBL mode.

    Note: To return the TV volume to the CBL Mode repeat steps above replacing [CBL] with [TV] in Step 3.Volume controls can be modified for all devices by following the above steps.
  • Programming a Macro" Button"
    If your remote control model has custom-programmable Macro buttons available (labeled *"), it can be programmed to act as a "Macro" or Favorite Channel button when the remote control is in CBL mode. This allows you to program up a favorite channel to the Macro button.

    To program the Macro buttons follow these steps:

    STEP 1 Press the [CBL] button to select the CBL mode.

    STEP 2 Press the [MACRO] button ("*") and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on.

    STEP 3 Enter the channel number for the channel you want programmed to the Macro button (for example, 007) using the Numeric Keys.

    STEP 4 Press the [CH+] button to store the channels that were entered. The [CBL] button will blink twice to confirm that the commands were stored.

    To access the programmed channels, press the [MACRO] button."
  • Memory Lock System
    This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.