Skip to Content

CLIKR-5 Backlit v4

Program Your Remote
The UR5U-8790L is a 5 device universal remote control that will control your cable box and up to 4 additonal devices, including TV's, VCR's and DVD players.

Download Remote Manual
Common Remote Keys

Control a Device

Select a Topic

  • Upgraded Features

    URC is introducing new, upgraded features in all cable remote control models. These require a very slight modification of programming steps.

    These changes are for new remote orders delivered after 3/1/2013.

    Download the NEW set up instructions

  • Batteries
    Before you program or operate the remote control, you must install two new AA alkaline batteries.

    STEP 1 Remove the battery compartment cover on the back of your remote control.

    STEP 2 Check battery polarity carefully, and install the batteries as shown in the illustration inside the battery compartment.

    STEP 3 Replace the battery compartment cover.
  • Introduction
    The CLIKR-5 UR5U-8790L is factory programmed to operate Motorola set-top boxes. This remote can also be programmed to operate Pioneer, Pace Micro, Samsung and Motorola digital set tops, plus the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below.

    CBL: Cable Set-top Box
    TV: Televisions
    VCR: VCRs and TV/VCR Combo units
    DVD: DVD Players
    AUX: Audio Receivers, Gaming Systems, Media PC's, etc.

    This easy-to-operate remote control provides complete control capability and features such as:

    - Factory programmed to Time Warner Cable Specifications
    - Fully backlit keypad
    - 3 Simple programming methods
    - Dedicated DVR and On Demand controls
    - System On/Off button to turn all devices on or off with a single button press
    - Channel and Volume lock to provide ease of operation
    - Customizable Macro buttons to store favorite channels

  • Replacing Batteries
    Before you program or operate the remote control, you must install two new AA alkaline batteries.

    STEP 1 Remove the battery compartment cover on the back of your remote control.

    STEP 2 Check battery polarity carefully, and install the batteries as shown in the illustration inside the battery compartment.

    STEP 3 Replace the battery compartment cover.
  • Operations
    Default settings for the remote control are as follows:

    Component Default: CABLE

    Channel Default: CABLE - Default controls for Channel +/- and numeric keys are through the CABLE device. Refer to Programming Channel Control" for information on changing this setting.

    Volume Default: Volume and Mute control are automatically transferred to the respective Device Mode you select, as follows:

    CBL: Cable Set-top Box
    TV: TV
    VCR: TV
    DVD: TV
    AUX: AUX.

    Refer to "Programming Volume Control" for information on changing these settings."
  • Programming the Remote Control
    There are three ways you can program your CLIKR-5 remote:

    The Quick Set-Up Method
    The Pre-Programmed 3-Digit Code Method
    The Auto-Search Method


    The Quick Set-Up Method is the fastest and easiest way to program the remote for devices made by major manufacturers using a one-digit code.

    The Pre-Programmed 3-Digit Code Method allows you to setup all the buttons for a device by entering 3-digit code numbers that correspond to a particular Component's manufacturer/brand.

    The Auto-Search Method scans through all the codes in the remote control in order to find the correct code for your device.

    IMPORTANT SETUP NOTE!
    In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR, DVD or AUX button, depending on what device you are programming the remote to operate.

    When you are in setup mode, the Device LED will light for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off and exit setup mode. You will need to start the programming process over if this occurs.
  • Quick Set-Up Programming Method
    STEP 1 Turn on the component you want to program. (Example: To program your TV, turn on the TV.)

    STEP 2 Point the remote at the component and press and hold the [DEVICE] key for 3 seconds until the Device LED blinks off and turns back on. Continue holding the [DEVICE] key and press the number keys, one at a time, starting with 1, then 2, 3, 4, 5, 6, 7, 8, 9, 0. Stop pressing the number keys as soon as the component turns off.

    STEP3 Release the [DEVICE] key to save the code. The Device LED will blink twice to confirm the code is stored. Repeat the steps above for all other components that you wish to program (TV, VCR, DVD, AUX).

    Note: You can refer to the Quick-Set Up Code Table in the User Guide to determine the number associated with your brand of device.
  • Pre-Programmed 3-Digit Code Programming Method
    STEP 1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, DVD, etc.).

    STEP 2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that the remote is in the programming mode. The LED will remain on for 30 seconds and the next step must be entered while the LED is on.

    STEP 3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand device (codes can be found in the code tables in the user guide or online). If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.

    Note: When the equipment turns off you can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 above using the next three digit code number from the brand list.

    STEP 4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
  • Auto-Search Programming Method
    If the Pre-Programmed 3-digit code method is unsuccessful or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following these steps:

    STEP 1 Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, DVD, etc.).

    STEP 2 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that the remote is in the programming mode. The LED will remain on for 30 seconds and the next step must be entered while the LED is on.

    STEP 3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.

    Note: When the equipment turns off you can verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, turn the device back on and repeat the instructions from STEP 3 to continue the Auto Search Method

    STEP 4 Store the three-digit code by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
  • To Identify the 3-Digit Code Programmed for a Device
    The 3-Digit code that is programmed into the remote can be identified by following these steps:

    STEP 1 Press the [DEVICE] button and the [OK/SEL] button simultaneously for three seconds.

    STEP 2 Press the [INFO] button. The Device LED will blink a number of times indicating the number for each digit for the code. Each digit is separated by a one second interval of the LED being off.

    Example: One blink, (pause) three blinks, (pause) eight blinks indicates code number 138.

    Note: Ten blinks indicates the number 0.
  • Programming the AUX Device
    You can take advantage of the AUX Device to program components such as a media PC, gaming console, satellite radio receiver and much more. The Pre-Programmed 3-Digit code Programming Method and the Auto-Search Programming Method can be used to program components listed as AUX" in the code tables. You can also program the AUX button for a second TV, VCR, or DVD Device. To do this follow these instructions:

    STEP 1 Turn on the 5th device you want to program (TV, VCR, DVD, etc.).

    STEP 2 Press the [AUX] button and the [OK/SEL] button simultaneously for 3 seconds. The [AUX] device LED will turn on for 30 seconds.

    STEP 3 Press the [Device] button For the type of device you want to setup. Point the remote control toward the device and enter the 3-digit code number assigned to your brand.

    Note: To program a second TV press TV, etc.

    STEP 4 When the equipment turns off verify that you have selected the correct code by pressing the [POWER] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, enter the next 3-digit code number from the code list.

    STEP 5 Once you have found the correct 3-digit code, save it by pressing the [AUX] button one more time. The [AUX] LED light will blink twice to confirm the code was stored."
  • Programming the System On/Off Button
    The System On/Off button can be programmed to send up to five Power On/Off commands with one button press. The remote control is factory programmed to send power commands for all five devices. The System On/Off button can be reprogrammed to send commands for the devices you choose by following these steps:

    STEP 1 Press the [CBL] button.

    STEP 2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds.

    STEP 3 Press the first [DEVICE] button you want to store power commands for in the [SYSTEM ON/OFF] button and then press [POWER]. Repeat this for the other components you want to turn on/off with the [SYSTEM ON/OFF] button.

    Example: [CBL], [Power], [TV], [Power]. etc.

    STEP 4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the commands have been saved.
  • Programming Volume Control
    Volume and Mute control are automatically transferred to the respective Device Mode you select, as follows:

    CBL: Cable Set-top Box
    TV: TV
    VCR: TV
    DVD: TV
    AUX: AUX.

    If you wish to store the TV volume controls in the CBL mode use the following steps:

    STEP 1 Press the [OK/SEL] button and [CBL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.

    STEP 2 Press the [VOL+] button. The device LED will blink.

    STEP 3 Press [TV] button. The device LED will blink twice to confirm the programming. Now the CBL volume will default to the TV allowing you to adjust the TV volume when the remote control is in CBL mode.

    Note: To return the CBL volume to the CBL Mode repeat steps above replacing [TV] with [CBL] in Step 3.Volume controls can be modified for all devices by following the above steps.
  • Programming Channel Control
    You can program the channel controls (Channel Up, Channel Down, Last and Numeric Keys) from one component to operate in another Device mode of the remote control. Default channel control settings on the remote control are as follows:

    CBL: CBL
    TV: CBL
    VCR: CBL
    DVD: DVD
    AUX: AUX.

    If you wish to store TV channel controls when the remote control is in TV mode, use the following steps:

    STEP 1 Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on.

    STEP 2 Press the [VOL-] button. The device LED will blink.

    STEP 3 Press [TV] button. The device LED will blink twice to confirm the programming. Now the remote control will operate the TV channel will default to TV allowing you to adjust the TV channels when the remote control is in TV mode.

    Note: To return CBL channel control to the TV mode of the remote control repeat steps above replacing [TV] with [CBL] in Step 3.
  • Programming a Macro" Button"
    If your remote control model has custom-programmable Macro buttons available (Labeled M1" or "M2"), they can be programmed to act as a "Macro" or Favorite Channel button when the remote control is in CBL mode. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels to each Macro button available. To program the Macro buttons follow these steps:

    STEP 1 Press the [CBL] button to select the CBL mode.

    STEP 2 Press the [MACRO] button (M1 or M2) and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on.

    STEP 3 Enter the 2, 3 or 4-digit channel number for the channel you want programmed first (for example, 007) using the Numeric Keys, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. Repeat this process for the third, fourth and fifth channel if applicable.

    STEP 4 Press the [CH+] button to store the channels that were entered. The [CBL] button will blink twice to confirm that the commands were stored.

    To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press the [MACRO] button again and it will bring up the second channel and so on."
  • Low Battery Warning
    The remote control has a built in test to determine if the batteries are low and need to be replaced with new batteries.

    Press the [POWER] button, if the Device LED lights blink 1 time each in sequence beginning with CBL and ending with AUX. It will repeat this sequence a second time. This indicates that the batteries are getting low.

    Note: This test only works with the POWER button and NOT with the System On/Off button.
  • Memory Lock System
    This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.