Skip to Content

TWC Philips Remote

Program Your Remote
The Philips remote control is designed to control the Time Warner Cable set top boxes along with the majority of TV, DVD, VCR and AUDIO devices on the market.

Download Remote Manual
Common Remote Keys

Control a Device

Select a Topic

  • Batteries

    The remote requires two AA batteries. A diagram inside the battery compartment of the remote indicates proper placement of the batteries. When batteries are properly installed, the light on theremote blinks each time a key is pressed.

  • Turning On/Off the Back Lighting Feature

    Press the  button to turn on/off this feature.

  • Programming Devices

    Your remote control is already programmed to control your set-top box. To control other devices (TV, VCR, DVD, AUX ), follow the steps below:

    1. Find the manufacturer’s code for your device.

    2. Turn on your device.

    3. Press and hold the SELECT/OK button and the the appropiate device
        key (TV, VCR, DVD, AUX) untill all the device keys blink twice.

    4. Enter the 4 digit code you found in step 1. All device keys will blink    
        three times to indicate that the code entry was accepted.

    5. Point the remote towards the device, and press

        
        to test the device.

    6. If the device operates correctly, write down the code that worked at
        the end of this manual. If not, repeat these steps using the
        next manufacturer’s code found in Step 1 (You may need to try
        several codes to find the one that works for your device). If you still
        can’t find a code that works, see the “Can’t Find Your Code?
        section.

    7. Repeat this procedure for each device you want to program. 

  • Can’t Find Your Code?

    If you can’t program your remote using the codes on this manual, follow the steps below to search for yourcode:

    1. Turn on your device.

    2. Press and hold the SELECT/OK button and the appropriate device
        key (TV, VCR, DVD, AUX) untill all the device keys blink twice.

    3. Press 991. The device key you selected in step 2 blinks twice. 

    4. Point the remote towards the device, then press the PLAY
        button one time. And press the SELECT/OK button as soon as
        the device powers off. 

    5. Verify the new code is correct by pressing the POWER button. Did
        the device power on again? If yes, press SELECT/OK to assign the
        code. If no, continue to the following steps:

    a) Turn the device on.

    b) Press (Rewind, for the previous Manufacturer Code) or
        (Fast Forward, for the next Manufacturer Code) key to
        the correct code.

    c) When the device turns off, press SELECT/OK to assign the
        code. 

    6. Repeate this procedure for each mode/device key you want to
        program.

  • Retrieving the correct code from your remote control

    In order to determine which device code was programmed inside your remote control, please follow these steps: 

    1. Press and hold SELECT/OK and the appropriate key (TV, VCR, DVD,
        AUX) until all device keys blink twice.

    2. Press 990. The device key you selected in step 1 blinks twice.

    3. Press 1 and then count the number of times the device key
        blinks. The number of blinks indicates the digit inthe code. For
        example, 4 blinks indicate the first digit in the code is 4. If the device
        key does not blink, the digit is 0. 

    4. Press 2 and then count the number of times the device key blinks.
        This number indicates the second number in the code.

    5. Press 3 and then count the number of times the device key blinks.
        This number indicates the third number in the code.

    6. Press 4 and then count the number of times the device key blinks.
        This number indicates the fourth number in the code.

    Note: After all four digits in the code are identified, the device keys will blink three times.

    7. Record the code in the table provided at the end of the user
        manual.

  • Setting Volume Control to Audio Device

    By default, the volume control is programmed to operate theTV. Follow these steps if you want to use your audio device to control the volume rather than the TV.

    1. Press and hold SELECT/OK and CBL key untill all device keys blink
        twice.

    2. Press 993. The CBL key blinks twice.

    3. Press the AUX key. All device keys blink three times.

    Note: You can set Volume Control back to TV. Follow the same process as mentioned above but just press the TV key in Step 3. 

  • Reset your Remote Control to Factory Settings

    Follow these steps in order to return the remote back to its original settings. 

    1. Press and hold SELECT/OK and CBL key until all device keys blink
        twice.

    2. Press 981. All device keys will blink three times. After few seconds
        the CBL key blinks twice.