• Program Your Remote
  • Volume Control
  • Common Buttons
  • Batteries
  • Troubleshooting Tips
  • Replace Your Remote

Overview

Program your Time Warner Cable remote to control your TV using the instructions below. There are two common ways to program your TWC remote to work with your TV and other devices, such as your DVD, DVR, etc.

Auto-Search Method (recommended)

Program your remote by displaying the code that works with your TV. This option scans through all of the codes in the remote control, one at a time, allowing you to identify the correct code.

Manual Method

Program your remote by looking up and then entering a code that corresponds with your TV brand.

Auto-Search Method (recommended)

The Auto-Search Method scans through all of the codes in the TWC remote control, one at a time, allowing you to identify the correct code. Follow these steps:
  1. Turn on the device, such as your TV, that you want the remote to operate.
  2. On your remote, press the device button (TV, AUX, or CABLE) once and then press and hold SETUP until the selected device button blinks twice.
  3. Press 9 9 1. The device button will blink twice.
  4. Point the remote at your device and slowly alternate between pressing POWER and the device button. Stop when your device turns off.
  5. Press SETUP to lock in the code. The device button will blink twice.

Note: If your remote does not control your device after following the steps above, try the Manual method.

Manual Method

You can set up the TWC remote control by entering a code that corresponds with your device’s brand. Using the filters below, select a device and a corresponding brand to see applicable codes.
If your brand is not listed, please open the PDF version of the manual to find your code then follow the instructions below.
Select a device:
Select the device brand:
Find your device codes using the dropdown options above, then follow these steps:
  1. Turn on the device, such as your TV, that you want the remote to operate.
  2. On your remote, press the device button (TV, AUX, or CABLE) once and then press and hold SETUP until the selected device button blinks twice.
  3. Point the remote at your device and enter a code assigned to your brand. If done correctly and with a valid code, the selected device button will blink twice.
    Note: When an invalid code is entered, the selected device button will display one long blink and exit programming. To continue, repeat steps 2-3 with a valid code. 
  4. Press POWER to test the device. The device should turn off.
  5. If your device turns off, programming is complete. If your device does not turn off, repeat steps 2 through 4 using the next code for your device.

Note:If your remote does not control your device after following the steps above, try the Auto-Search method.

Volume Control

Once your TWC remote control has been programmed to turn your TV on and off, it is automatically set up to control your TV’s volume.

 

Commonly Used Buttons

Understanding the buttons on your TWC Remote is essential to unlocking its full potential.
 
POWER turns off the device, such as AUX, TV or CBL, that is currently selected.
 
SYSTEM ON/OFF turns on or powers off all devices that are programmed through the remote.
 
Press GUIDE once to display the program guide on your TV screen. Press it again to filter channels.
 
MENU open the cable box's menu, allowing you to access Search, On Demand and Guide information.
 
INFO displays information about the program you are watching or a selected program in the Guide.
 
EXIT the program guide and go back to live programming. EXIT also clears on-screen displays.
 
SETTINGS displays a list of options -- set your favorite channels, program parental controls and adjust your display.
 
SELECT or OK selects a highlighted program or menu item and confirms a selection.
 
A opens the cable box's menu, allowing you to access Search, On Demand and Guide information.
 
B opens the search function, allowing you to search for a program by show title or actor name.
 
C steps you back one menu layer. It's useful when configuring settings and acts like the EXIT button.
 
LAST (or PREV CH) allows you to toggle between the last two selected channels.
 
ON DEMAND opens the On Demand channel. This is a macro button.
 
LIST is used with a DVR. It displays a list of your recorded shows and movies.
 
LIVE is used with a DVR. It changes to "live" programming when you are watching a show that's behind the current time.
 
#/ASPECT cycles the on-screen picture among Normal, Stretch and Zoom.
 
VIDEO SOURCE changes the TV's input source, such as a Set-Top Box, gaming system or Roku.

Buttons may vary by remote brand and model.
 

Batteries

If your TWC remote begins to malfunction, your batteries might need to be replaced.

Installing/Replacing
  1. Remove the battery cover on the back of your remote and take out the old batteries.
  2. Carefully install two new AA batteries as shown in the illustration inside the battery cover.
  3. Replace the battery cover.

Troubleshoot Your Remote

If your remote control is not working, please try the following:

  1. Replace the batteries.
  2. Check that there are no obstructions between the sensor on the Set-Top Box and the transmitter on the remote control. There must be a clear line of sight between the two.
  3. Check for an error message on the Set-Top Box. If the error message is number 1103 or 232, contact us with the displayed number. If the error message is any other number, try rebooting your Set-Top Box.
  4. Reprogram the remote to your device(s).

 

POWER is not turning your device on or off.

  1. Press the corresponding device button then press POWER.
  2. If the device does not turn off, reprogram the remote to your device.

SYSTEM ON/OFF is not controlling all of your devices.

  1. Press the device button, such as TV, CBL or AUX, that corresponds to the device that isn’t responding and then press POWER.
  2. With all devices now on (or off), press SYSTEM ON/OFF to sync.
  3. All devices should turn off (or on). If the device does not turn off, reprogram the remote to your device.

VIDEO SOURCE is not displaying additional devices when more than one device is connected to the TV.

  1. Press the TV device button on the remote and try VIDEO SOURCE again.
    Note: If the list displays nothing only one device is connected.

ON DEMAND does not take you to the correct On Demand channel.

  1. To reprogram the On Demand button see our step-by-step instructions for programming macro buttons.

Other buttons, such as volume +/-, mute and channel up/down, don’t seem to be working.

  1. Press the device button, such as TV or CBL, that is programmed to control that buttons function.
  2. Verify if the button is working. If it does not respond, reprogram the remote to operate that device.
  3. If the problem persists, then the buttons on your remote may be worn out. To trade it in, bring it to a local TWC Store or contact us.

Remote turns off the TV on its own or responds inconsistently.

  1. Replace the batteries.
  2. If the problem persists, then the buttons on your remote may be worn out. To trade it in, bring it to a local TWC Store or contact us.

Setting favorite channels:

  1. Press the SETTINGS button.
  2. Select FAVORITE CHANNEL from the menu on the bottom of the screen.
  3. Use the UP/DOWN arrows on the remote to locate and highlight a channel.
  4. Press OK/SELECT – a star should appear by the channel.
  5. Press the C button to save.

Get detailed instructions for using The Guide to find shows and channels, adjust settings, order On Demand or Pay-Per-View events with ease.

Replace Your Remote

If you have tried replacing your batteries and you are still having issues with your TWC remote control, it may be time to trade it in. Bring your old remote with you to a local TWC Store and trade it for a newer model or contact us for a replacement.